NC-CylinderElf-IV-D New machine installation and debugging

32 Lượt xem

Thích hợp NC-Xi lanhElf-IV-D New machine installation and debugging​ makes your 360° rotary UV printer production-ready from day one. The NC-CylinderElf-IV-D is Nocai’s high-speed tumbler UV printer with RICOH GEN6×5 printheads as standard (GEN6×6 optional), delivering 720×900 to 960×1200 dpi in CMYK+LC+LM+W+V+Pr mode. It prints objects 80–280 mm long and Φ45–160 mm in diameter, with taper <5° and 2–20 mm high-drop capability—ideal for tumblers, chai, gốm sứ, and cylindrical electronics. The machine measures 1994×913×1535 mm, weighs 400 kg, and requires AC 220V, 50/60Hz, 1500W. Commissioning correctly—uncrating, levelling, driver and RIIN setup, ink filling, and test printing—ensures stable, seamless 360° output.

Site Preparation and Uncrating

Place the printer indoors on a stable floor that can support 400 kg. Maintain ambient temperature 25–28°C and humidity 35–65% RH; avoid dust, open flames, and wet environments. Provide a dedicated grounded AC 220V power supply. Remove the wooden case and the foot-cup fixing frame, then place the printer on a stable table. Adjust the four foot cups and use a spirit level to make the machine level both left-right and front-back.

Driver and RIIN Installation

Prepare a host computer meeting Nocai’s requirements. Install the driver package as administrator, then install the RIIN RIP software. During RIIN setup, select the NC-Cylinder Elf printer profile, configure the canvas and coordinate origin, and modify the interface language as needed. Confirm the RIIN dongle is recognized by the system.

Adding Ink

Theo dõi “How to Add Ink” chapter, fill each color with genuine Nocai UV ink. Shake white ink thoroughly and add ink in small, frequent amounts. Monitor the ink alarm indicator—add until the alarm clears, then slightly more. Use only Nocai original ink and original supplier’s spare parts to maintain warranty coverage.

Manual Inking and Negative Pressure

Ở chế độ chờ, open the valve and enter the manual inking function to purge air from each channel—typically 3–5 seconds per channel, following the 1-3-2-4 connection order. Adjust the negative pressure value on the control board (ví dụ., -125) until stable. Then run Auto Cleaning and print a nozzle test strip via the TEST key. Repeat manual head cleaning if missing nozzles appear.

Fixture and Print Height Setup

Measure the bottle and modify driver parameters accordingly. Select a suitable fixture and clamp the bottle firmly—change the fixture shell by loosening three screws if the bottle diameter requires it. In the engineering mode, adjust the clamp position and lower the print height appropriately (ví dụ., ĐẾN -500) before restarting. Adjust the tilt angle to match the bottle taper, keeping it under 5°. Align the bottle height with the light-blocking plate using a hex key as reference.

Test Printing and Acceptance

Before printing, confirm the UV lamp water machine is normal—connect the control line, add the appropriate amount of pure water, and ensure power is normal. In RIIN, set up the graphics and click Send to start printing. The bottle resets automatically when printing completes. Check the test strip: the top section verifies horizontal calibration, the bottom thin lines verify vertical alignment, each color aligned to black as the reference. Print a small frame to check for color leakage or ghosting. Once the test print meets quality standards, the NC-CylinderElf-IV-D New machine installation and debugging​ is complete and the printer is ready for full production.

Post-Commissioning Care

Maintain workshop temperature at 25–28°C and humidity 35–65% RH. Stir ink regularly and enable the ink-stirring function. If idle beyond 3 ngày, add 3–5 drops of cleaning fluid into the cap top and seal the nozzle. Use only Nocai original UV ink and cleaning solution. Nocai provides free on-site installation, commissioning, and operator training through its global service network—contact your local dealer for support.